[OLUG] soundcard
mesc
mescie at home.com
Wed Mar 22 15:25:46 UTC 2000
mesc wrote:
> I'm trying to configure my Aztech 3011 soundcard (soundblaster
> compatible) in my mandrake 7.0 box. But at bootup I get this
> message>>Don't know what to do with CONFIGURE AZT3011/-1 (LD 1 on or
> around line 72
> /etc/isapnp.conf:72 -- Fatal - Error occurred parsing config file --- no
> action taken.............My I/O's are 0220-022F,0388-038F,0534-0537 irq
> 5 and DMA's 1,0 I've tried comenting out CONFIGURE AZT3011/-1 but I
> still got the same error.
> Also when I try to load the sb module from /sbin using modprobe sb
> I get this error>>/lib/modules/2.2.14-15mdk/misc/sb.o: init_module:
> Device or resource busy
> sound: Device or resource busy.
> I've included the isapnp.cong file if anyone cares to look at it and
> see where I went wrong.
>
> Thank you,Gary Martin
>
Duh at me I forgot to atach my isapnp.conf file :)Here it is.
Gary Martin
>
> -------------------------------------------------------------------------
> Sent by OLUG Mailing list Manager, run by ezmlm. http://olug.bstc.net/
> To unsubscribe: `echo unsubsribe | mail olug-unsubscribe at bstc.net`
-------------- next part --------------
# $Id: pnpdump.c,v 1.20 1999/12/02 22:39:24 fox Exp $
# Release isapnptools-1.20
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR
#
# Trying port address 0273
# Board 1 has serial identifier 07 ff ff ff ff 11 30 54 07
# Board 2 has serial identifier 9a da c5 67 b3 95 50 6d 50
# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
# Card 1: (serial identifier 07 ff ff ff ff 11 30 54 07)
# Vendor Id AZT3011, No Serial Number (-1), checksum 0x07.
# Version 1.0, Vendor version 0.3
# ANSI string -->AZT3011 PnP SOUND DEVICE<--
#
# Logical device id AZT0500
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 0
# ANSI string -->IDE CDROM DISABLED<--
#
# Multiple choice time, choose one only !
#
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0000
# Maximum IO base address 0x0000
# IO base alignment 8 bytes
# Number of IO addresses required: 0
# (IO 0 (SIZE 0) (BASE 0x0000) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0000
# Maximum IO base address 0x0000
# IO base alignment 2 bytes
# Number of IO addresses required: 0
# (IO 1 (SIZE 0) (BASE 0x0000) (CHECK))
# *** ERROR *** No IRQ specified!
#
# End dependent functions
# (NAME "AZT3011/-1[0]{IDE CDROM DISABLED }")
# (ACT Y)
# ))
#
# Logical device id AZT1003
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
#
(CONFIGURE AZT3011/-1 (LD 1
# ANSI string -->AUDIO<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 16 bytes
# Number of IO addresses required: 16
(IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 8
(IO 1 (SIZE 8) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0534
# Maximum IO base address 0x0534
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0534) (CHECK))
IRQ 5.
# High true, edge sensitive interrupt
(INT 0 (IRQ 5 (MODE +E)))
First DMA channel 1.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
(DMA 0 (CHANNEL 1))
# Next DMA channel 0.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
(DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
(IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 8
(IO 1 (SIZE 8) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0534
# Maximum IO base address 0x0608
# IO base alignment 212 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0534) (CHECK))
IRQ 5
# High true, edge sensitive interrupt
(INT 0 (IRQ 5 (MODE +E)))
First DMA channel 1
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
(DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
(IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 8
(IO 1 (SIZE 8) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0e84
# Maximum IO base address 0x0f44
# IO base alignment 192 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0e84) (CHECK))
# IRQ 5, 9 or 10.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
(DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x0ffc
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0100) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x0ffc
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0100) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# End dependent functions
(NAME "AZT3011/-1[1]{AUDIO }")
(ACT Y)
))
#
# Logical device id AZT2001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
#(CONFIGURE AZT3011/-1 (LD 2
# ANSI string -->MPU401 MIDI<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0330) (CHECK))
# IRQ 9.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 9 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0300) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03fe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0100) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# End dependent functions
(NAME "AZT3011/-1[2]{MPU401 MIDI }")
# (ACT Y)
))
#
# Logical device id AZT3001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 3
# ANSI string -->GAME PORT<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0200
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200) (CHECK))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0208
# Maximum IO base address 0x0208
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0208) (CHECK))
# End dependent functions
(NAME "AZT3011/-1[3]{GAME PORT }")
# (ACT Y)
))
#
# Logical device id AZT4014
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 4
# ANSI string -->MODEM<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0110
# Maximum IO base address 0x0110
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0110) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0170
# Maximum IO base address 0x0170
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0170) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0210
# Maximum IO base address 0x0210
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0210) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0270
# Maximum IO base address 0x0270
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0270) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x02e0
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0100) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# End dependent functions
(NAME "AZT3011/-1[4]{MODEM }")
# (ACT Y)
))
#
# Logical device id AZT5001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 5
# ANSI string -->EEPROM<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03ff
# IO base alignment 1 bytes
# Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0100) (CHECK))
# End dependent functions
(NAME "AZT3011/-1[5]{EEPROM }")
# (ACT Y)
))
# Version 1.0, Vendor version 0.3
# ANSI string -->AZT3011 PnP SOUND DEVICE<--
#
# Logical device id AZT0500
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 0
# ANSI string -->IDE CDROM DISABLED<--
#
# Multiple choice time, choose one only !
#
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0000
# Maximum IO base address 0x0000
# IO base alignment 8 bytes
# Number of IO addresses required: 0
# (IO 0 (SIZE 0) (BASE 0x0000) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0000
# Maximum IO base address 0x0000
# IO base alignment 2 bytes
# Number of IO addresses required: 0
# (IO 1 (SIZE 0) (BASE 0x0000) (CHECK))
# *** ERROR *** No IRQ specified!
#
# End dependent functions
# (NAME "AZT3011/-1[0]{IDE CDROM DISABLED }")
# (ACT Y)
# ))
#
# Logical device id AZT1003
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
#
(CONFIGURE AZT3011/-1 (LD 1
# ANSI string -->AUDIO<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0534
# Maximum IO base address 0x0534
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0534) (CHECK))
# IRQ 5.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
# Next DMA channel 0.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0534
# Maximum IO base address 0x0608
# IO base alignment 212 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0534) (CHECK))
# IRQ 5, 9 or 10.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0e84
# Maximum IO base address 0x0f44
# IO base alignment 192 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0e84) (CHECK))
# IRQ 5, 9 or 10.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x0ffc
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0100) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x0ffc
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0100) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# End dependent functions
(NAME "AZT3011/-1[1]{AUDIO }")
# (ACT Y)
))
#
# Logical device id AZT2001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 2
# ANSI string -->MPU401 MIDI<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0330) (CHECK))
# IRQ 9.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 9 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0300) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03fe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0100) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# End dependent functions
(NAME "AZT3011/-1[2]{MPU401 MIDI }")
# (ACT Y)
))
#
# Logical device id AZT3001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 3
# ANSI string -->GAME PORT<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0200
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200) (CHECK))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0208
# Maximum IO base address 0x0208
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0208) (CHECK))
# End dependent functions
(NAME "AZT3011/-1[3]{GAME PORT }")
# (ACT Y)
))
#
# Logical device id AZT4014
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 4
# ANSI string -->MODEM<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0110
# Maximum IO base address 0x0110
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0110) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0170
# Maximum IO base address 0x0170
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0170) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0210
# Maximum IO base address 0x0210
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0210) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0270
# Maximum IO base address 0x0270
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0270) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x02e0
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0100) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# End dependent functions
(NAME "AZT3011/-1[4]{MODEM }")
# (ACT Y)
))
#
# Logical device id AZT5001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 5
# ANSI string -->EEPROM<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03ff
# IO base alignment 1 bytes
# Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0100) (CHECK))
# End dependent functions
(NAME "AZT3011/-1[5]{EEPROM }")
# (ACT Y)
))
# Version 1.0, Vendor version 0.3
# ANSI string -->AZT3011 PnP SOUND DEVICE<--
#
# Logical device id AZT0500
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 0
# ANSI string -->IDE CDROM DISABLED<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0000
# Maximum IO base address 0x0000
# IO base alignment 8 bytes
# Number of IO addresses required: 0
(IO 0 (BASE 0x534))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0000
# Maximum IO base address 0x0000
# IO base alignment 2 bytes
# Number of IO addresses required: 0
(IO 1 (BASE 0x300))
# *** ERROR *** No IRQ specified!
# End dependent functions
(NAME "AZT3011/-1[0]{IDE CDROM DISABLED }")
# (ACT Y)
))
#
# Logical device id AZT1003
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
#(CONFIGURE AZT3011/-1 (LD 1
# ANSI string -->AUDIO<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 16 bytes
# Number of IO addresses required: 16
(IO 0 (BASE 0x220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0534
# Maximum IO base address 0x0534
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0534) (CHECK))
# IRQ 5.
# High true, edge sensitive interrupt
(INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
(DMA 0 (CHANNEL 1))
# Next DMA channel 0.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
(DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0534
# Maximum IO base address 0x0608
# IO base alignment 212 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0534) (CHECK))
# IRQ 5, 9 or 10.
# High true, edge sensitive interrupt
(INT 0 (IRQ 7 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0e84
# Maximum IO base address 0x0f44
# IO base alignment 192 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0e84) (CHECK))
# IRQ 5, 9 or 10.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x0ffc
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0100) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x0ffc
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0100) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# End dependent functions
(NAME "AZT3011/-1[1]{AUDIO }")
(ACT Y)
))
#
# Logical device id AZT2001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 2
# ANSI string -->MPU401 MIDI<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0330) (CHECK))
# IRQ 9.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 9 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0300) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03fe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0100) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# End dependent functions
(NAME "AZT3011/-1[2]{MPU401 MIDI }")
# (ACT Y)
))
#
# Logical device id AZT3001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 3
# ANSI string -->GAME PORT<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0200
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200) (CHECK))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0208
# Maximum IO base address 0x0208
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0208) (CHECK))
# End dependent functions
(NAME "AZT3011/-1[3]{GAME PORT }")
# (ACT Y)
))
#
# Logical device id AZT4014
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 4
# ANSI string -->MODEM<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0110
# Maximum IO base address 0x0110
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0110) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0170
# Maximum IO base address 0x0170
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0170) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0210
# Maximum IO base address 0x0210
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0210) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0270
# Maximum IO base address 0x0270
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0270) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x02e0
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0100) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# End dependent functions
(NAME "AZT3011/-1[4]{MODEM }")
# (ACT Y)
))
#
# Logical device id AZT5001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 5
# ANSI string -->EEPROM<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03ff
# IO base alignment 1 bytes
# Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0100) (CHECK))
# End dependent functions
(NAME "AZT3011/-1[5]{EEPROM }")
# (ACT Y)
))
# Version 1.0, Vendor version 0.3
# ANSI string -->AZT3011 PnP SOUND DEVICE<--
#
# Logical device id AZT0500
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 0
# ANSI string -->IDE CDROM DISABLED<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0000
# Maximum IO base address 0x0000
# IO base alignment 8 bytes
# Number of IO addresses required: 0
(IO 0 (BASE 0x534))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0000
# Maximum IO base address 0x0000
# IO base alignment 2 bytes
# Number of IO addresses required: 0
(IO 1 (BASE 0x330))
# *** ERROR *** No IRQ specified!
# End dependent functions
(NAME "AZT3011/-1[0]{IDE CDROM DISABLED }")
(ACT Y)
))
#
# Logical device id AZT1003
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 1
# ANSI string -->AUDIO<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 16 bytes
# Number of IO addresses required: 16
(IO 0 (BASE 0x220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0534
# Maximum IO base address 0x0534
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0534) (CHECK))
# IRQ 5.
# High true, edge sensitive interrupt
(INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
(DMA 0 (CHANNEL 1))
# Next DMA channel 0.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
(DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0534
# Maximum IO base address 0x0608
# IO base alignment 212 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0534) (CHECK))
# IRQ 5, 9 or 10.
# High true, edge sensitive interrupt
(INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0e84
# Maximum IO base address 0x0f44
# IO base alignment 192 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0e84) (CHECK))
# IRQ 5, 9 or 10.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x0ffc
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0100) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 1 (SIZE 8) (BASE 0x0100) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x0ffc
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0100) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# End dependent functions
(NAME "AZT3011/-1[1]{AUDIO }")
(ACT Y)
))
#
# Logical device id AZT2001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 2
# ANSI string -->MPU401 MIDI<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0330) (CHECK))
# IRQ 9.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 9 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0300) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03fe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0100) (CHECK))
# IRQ 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 5 (MODE +E)))
# End dependent functions
(NAME "AZT3011/-1[2]{MPU401 MIDI }")
# (ACT Y)
))
#
# Logical device id AZT3001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 3
# ANSI string -->GAME PORT<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0200
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200) (CHECK))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0208
# Maximum IO base address 0x0208
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0208) (CHECK))
# End dependent functions
(NAME "AZT3011/-1[3]{GAME PORT }")
# (ACT Y)
))
#
# Logical device id AZT4014
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 4
# ANSI string -->MODEM<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0110
# Maximum IO base address 0x0110
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0110) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0170
# Maximum IO base address 0x0170
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0170) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0210
# Maximum IO base address 0x0210
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0210) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0270
# Maximum IO base address 0x0270
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0270) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x02e0
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0100) (CHECK))
# IRQ 3, 4, 5, 9, 10, 11 or 15.
# High true, edge sensitive interrupt
# (INT 0 (IRQ 3 (MODE +E)))
# End dependent functions
(NAME "AZT3011/-1[4]{MODEM }")
# (ACT Y)
))
#
# Logical device id AZT5001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE AZT3011/-1 (LD 5
# ANSI string -->EEPROM<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03ff
# IO base alignment 1 bytes
# Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0100) (CHECK))
# End dependent functions
(NAME "AZT3011/-1[5]{EEPROM }")
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Card 2: (serial identifier 9a da c5 67 b3 95 50 6d 50)
# Vendor Id TCM5095, Serial Number 3670370227, checksum 0x9A.
# Version 1.0, Vendor version 1.0
# ANSI string -->3Com 3C509B EtherLink III<--
#
# Logical device id TCM5095
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE TCM5095/3670370227 (LD 0
# Compatible device id PNP80f7
# IRQ 3, 5, 7, 9, 10, 11, 12 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0210
# Maximum IO base address 0x03e0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0210) (CHECK))
(NAME "TCM5095/3670370227[0]{3Com 3C509B EtherLink III}")
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
-------------- next part --------------
-------------------------------------------------------------------------
Sent by OLUG Mailing list Manager, run by ezmlm. http://olug.bstc.net/
To unsubscribe: `echo unsubsribe | mail olug-unsubscribe at bstc.net`
More information about the OLUG
mailing list